HL-DT-ST DVD GDR8162B DRIVER DOWNLOAD

Try another data cable if in doubt. If that doesn’t help, you may need to change a setting regarding drive detection – e. I have discovered I have the same model sitting around. XP has no built in software codec that can read encoded DVDs, such as pre-recorded movies. It should either show up in the bios Setup, or if you have an old mboard, the model of the drive should show up on the first black screen while booting the computer. Usually the thing that makes them un-usable first is the cheap sleeve bearings in the motor have worn to the point that so much friction is produced in the bearings that the motor can no longer spin at the minimum 1X legacy audio CD speed, or the motor doesn’t spin at all. Solved i need the drivers for Hl-dt-st dvd-rom gdrb instalation.

Uploader: JoJokasa
Date Added: 8 March 2015
File Size: 21.42 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 81353
Price: Free* [*Free Regsitration Required]

What the pins are for is stamped into the metal on top of the drive. The side of the data ddvd that has a colored stripe must be next to the 4 pin power socket. Such opinions may not be accurate and they are to be used at your own risk. Net and its accuracy. If you have a generic system and have the CD that came with the mboard, all the necessary drivers are on it. Try another data cable if in doubt.

Hl-dt-st dvd-rom gdr8162b

XP has no built in software codec that can read encoded DVDs, such as pre-recorded movies. Net is the opinions of its users. It is common to un-intentionally damage IDE data cables, especially while removing them – the 80 wire ones are more likely to be damaged.

Default bios settings are usually already set so any drive that is properly connected, and has the proper jumper setting if it’s an IDE drive, will be detected If you think bios settings may have been set wrong, load bios defaults, Save bios settings.

  ASUS P5WDH DELUXE AUDIO DRIVER DOWNLOAD

Usually the thing that makes them un-usable first is the cheap sleeve bearings in the motor have worn to the point that so much friction is produced in the bearings that the motor can no longer spin at the minimum 1X legacy audio CD speed, or the motor doesn’t spin at all. Make sure that there are no pins on the drive or on the mboard IDE headers that are bent over such that they’re not plugging into the data cable connectors.

What usually happens is the cable is ripped at either edge and the wires there are either damaged or severed, often right at a connector or under gdt8162b cable clamp there, where it’s hard to see – if a wire is severed but it’s ends are touching, the connection is intermittent, rather than being reliable.

You don’t need to install drivers for it.

HL-DT-ST DVD-ROM GDRB USB Device Drivers Download for Free | Driver Talent

Yes No I don’t have a dog. That model is relatively old.

XP doesn’t have the drivers built in for most things that first came out after XP was first released, circaand it doesn’t have some of the drivers built in for things made before that. The jumper setting on the back of the drive must be set properly. If that doesn’t help, you may need to change a hl-dt-wt regarding drive detection – e. Over gd8r162b Month Ago Time Zone: I have discovered I have the same model sitting around.

Another common thing is for the data cable to be separated from the connector contacts a bit after you have removed a cable – there should be no gap between the data cable and the connector – if there is press the cable against the connector to eliminate the gap.

Your drive does not require an 80 wire data cable – a 40 wire one will do – but if it’s on the same data cable as a hard drive that requires an 80 wire data cable, you must use an 80 wire data cable to get the full max burst speed from the hard ggdr8162b. Usually hl-dt-sy pin gdr8126b end of the IDE header on the drive is next to the power socket. Would you use Snapchat filters on your dog?

  INTEL 2230 WLAN CARD 802.11N DRIVER DOWNLOAD

There must be a jumper on one of those three pairs of pins.

If it is possible for a data cable connector to plug into a IDE header either way, the striped side of the data cable must be next to the pin one end of the IDE header on all connections.

Use Question Form such as ” Why? Solved i need the drivers for Hl-dt-st dvd-rom gdrb instalation. The information on Computing. There are two rows of 3 pins on the back of the drive next to the pins for yl-dt-st IDE header.

Net cannot verify the validity of the statements made on this site.

[Solved] i need the drivers for Hl-dt-st dvd-rom gdrb instalation

Thousands of users waiting to help! It may NOT be able to recognize some types of “burned” dvs that already have data on them.

Do you have a problem with the drive not being detected at all, or the drive is being detected but it is not working properly? It should either show up in the bios Setup, or if you have an old mboard, the model of the drive should show up on the first black screen while vdd the computer.